Kapasitas Lentur Balok Beton Ringan Dengan Penambahan Serat Ijuk

Mufti Amir Sultan, Erwinsyah Tuhuteru, M. Fadli Fajar Abdullah

Abstract


Lightweight concrete is concrete that has a specific gravity that is lighter than ordinary concrete. Lightweight concrete can be interpreted as concrete that has a volume weight between 1400-1850 kg/m3. The use of materials that have a light density in the concrete mix will reduce the overall weight of the concrete, thereby reducing the dimensions of the structure and can reduce structural loads, especially dead loads. Pumice or pumice is an aggregate that is classified as light aggregate. This type of stone is widely spread in the North Maluku region. In this study, pumice stone was used as a coarse aggregate for making concrete, the use of pumice as a coarse aggregate tends to reduce the compressive strength, so fiber fibers were used as an added material to the concrete mixture so that fiber concrete was obtained. . This study uses experimental methods, cylindrical specimens with 15 cm and height 30 cm for compressive strength testing, beam test specimens with a size of 15 cm x 20 cm x 120 cm for flexural strength testing. The reinforcement in the concrete beam is varied with variations of 2 reinforcement, 3 reinforcement and 4 reinforcement. The test results show that the use of palm fiber as an added material for the manufacture of lightweight concrete can increase the compressive strength of concrete by 11.70% against lightweight concrete without fibers. The addition of 4 reinforcement at the bottom of the beam tends to increase the capacity of the lightweight concrete beam by 3.28%.


Full Text:

PDF

References


ACI 213R-2014, Guide for Structural Lightweight Agregate Concrete. 2014.

SNI 03-3449, Tata Cara Rencana Pembuatan Campuran Beton Ringan Dengan Agregat Ringan. 2002.

K. Miswar, “Beton Ringan Dengan Menggunakan Limbah Styrofoam,” Portal J. Tek. Sipil, vol. 10, no. 1, pp. 33–39, 2018.

X. I. Alex and K. Arunachalam, “Flexural Behavior Of Fiber Reinforced L ightweight Concrete,” Rev. la Constr., vol. 18, no. 3, pp. 536–544, 2019.

P. Gunawan, A. S. Budi, and K. D. Wicaksono, “Kuat Lentur, Toughness, Dan Stiffness Pada Beton Ringan,” e-Jurnal Matriks Tek. Sipil, vol. 2, no. 2, pp. 109–116, 2014.

S. P. Sangeetha, R. Divahar, K. Mawlong, B. Lyngkhoi, and A. Kurkalang, “Mechanical Characteristics of Pumice Stone as Light Weight Aggregate in Concrete,” Int. J. Sci. Technol. Res., vol. 9, no. 1, pp. 3760–3762, 2020.

A. Gaus, M. A. Sultan, R. Hakim, and I. Anggreni, “Substitusi Parsial Batu Apung Sebagai Agregat Kasar Pada Campuran Beton,” J. Tek. Sipil Univ. Teuku Umar, vol. 6, no. 2, pp. 11–19, 2020.

P. Selvaprasanth, S. M. Kumar, and S. Indumathi, “Development Of Light Weight Concrete Using Pumice Stone,” Int. Res. J. Eng. Technol., vol. 6, no. 2, pp. 2003–2004, 2019.

S. Eliazer et al., “Perilaku Mekanis Beton Menggunakan Batuan Vulkanik (Batu Angus dan Batu Apung),” J. Tekno, vol. 17, no. 71, pp. 17–20, 2019.

M. A. Sultan, M. T. Yudasaputra, and A. Gaus, “The Use Of Pumice As Raw Material For Cement Brick,” Int. J. Civ. Eng. Technol., vol. 10, no. 12, pp. 498–504, 2019.

L. Malino, S. E. Wallah, and B. D. Handono, “Pemeriksaan Kuat Tekan Dan Kuat Tarik Lentur Beton Serat Kawat Bendrat Yang Ditekuk Dengan Variasi Sudut Berbeda,” J. Sipil Statik, vol. 7 (6), no. ISSN 2337-6732, pp. 711–722, 2019.

H. A. Haq and R. Andayani, “Pengaruh Penambahan Serat Kawat Bendrat Dan Serat Ijuk Pada Beton K-225 Terhadap Kuat Geser the Effect of Bendrat Fiber and Palm Fiber Increment on K-255 Concrete Toward Shear Streght,” J. Desain Konstr., vol. 16, no. 1, pp. 76–82, 2017.

Y. L. D. Adianto, “Pengaruh Penambahan Serat Nylon terhadap Kinerja Beton,” Pengaruh Penambahan Serat Nylon terhadap Kinerja Bet., vol. 12, no. 2, pp. 1–12, 2004.

S. W. Megasari, G. Yanti, and Z. Zainuri, “Karakteristik Beton Dengan Penambahan Limbah Serat Nylon Dan Polimer Concrete,” SIKLUS J. Tek. Sipil, vol. 2, no. 1, pp. 24–33, 2016.

S. Pratiwi, H. Prayuda, and F. Prayuda, “Kuat Tekan Beton Serat Menggunakan Variasi Fibre Optic dan Pecahan Kaca (Compressive Strength of Fibre Concrete Using Fibre Optic Variation and Glass Fracture),” Semesta Tek., vol. 19, no. 1, pp. 55–67, 2016.

Z. Zainuddin, “Pengaruh Penambahan Serat Sabut Kelapa Pada Beton Normal Dengan Uji Tekan dan Kuat Lentur,” D’teksi, vol. 4, no. 2, pp. 36–47, 2012.

H. Apriyanto, “Kapasitas Lentur Balok beton Bertulang Dengan Serat Sabut Kelapa,” J. Tek. Sipil dan Perenc., vol. 1, no. 13, pp. 45–52, 2013.

M. Suhardiman, “Kajian Pengaruh Penambahan Serat Bambu Ori Terhadap Kuat Tekan Dan Kuat Tarik Beton,” J. Tek., vol. Vol. 1 No., p. 8, 2011.

A. Junaidi, “Pemanfaatan Serat Bambu Untuk Meningkatkan Kuat Tekan Beton,” Berk. Tek., vol. 5, no. 1, p. 754, 2015.

N. Rochmah, “Pengaruh Serat Ijuk Sebagai Bahan Tambah Terhadap Kuat Tarik Belah Beton,” J. Penelit. LPPM Untag Surabaya, vol. 02, no. 01, pp. 52–56, 2017.

C. Anwar, E. Bachtiar, and K. N. Nur, “Sifat Mekanik Beton Serat Ijuk Yang Terendam Air Laut,” Indones. J. Fundam. Sci., vol. 5, no. 1, pp. 26–32, 2019.

SNI 1972, “Cara uji slump beton,” in Badan Standardisasi Nasional, 2008, p. 11.

SNI 03-1974, “Metode Pengujian Kuat Tekan Beton,” in Badan Standardisasi Nasional Indonesia, 1990.

SNI 4431, Cara uji kuat lentur beton normal dengan dua titik pembebanan, no. 1–12. 2011.




DOI: https://doi.org/10.35308/jts-utu.v7i2.4094

Refbacks

  • There are currently no refbacks.


Copyright (c) 2021 Jurnal Teknik Sipil dan Teknologi Konstruksi