Orientation Effect on Statics and Natural Frequency of Cantilever Beam

Ardi Noerpamoengkas, Miftahul Ulum, Ahmad Yusuf Ismail

Abstract


Statics and frequency analyzes are important because the structure can support the static and dynamic loads. Most previous studies of statics and frequency did not involve the gravity load. The previous studies of gravity effect to the cantilever beam included the hanging, horizontal, and inverted positions. The gravity load direction is applied referred to the longitudinal and lateral beam directions in this study. The closer to the inverted position the smaller the natural frequency. The highest values of the maximum displacement and the maximum Von-Mises stress are happened if longitudinal position is horizontal and lateral orientation angle is 0°. The change of lateral orientation angle does not influence the natural frequency in this condition.

 

Keywords—Cantilever beam, gravity load, natural frequency, orientation angle, statics


Full Text:

PDF

References


REFERENCES

M. R. Usal, M. Usal, and Ü. Esendemir, “Static and Dynamic Analysis of Simply Supported Beams,” J. Reinf. Plast. Compos., vol. 27, no. 3, pp. 263–276, Feb. 2008.

M. Awwaluddin and T. P. Soemardi, “ANALISIS TEGANGAN STATIK DAN DINAMIK PADA PERANCANGAN DAN PENGEMBANGAN STRUKTUR BODI MONORAIL PRODUKSI PT. MBW MENGGUNAKAN FINITE ELEMENT ANALYSIS (ANSYS),” in Seminar Universitas Indonesia, 2013.

A. Y. Ismail, A. Noerpamoengkas, and S. I. F. S. Zakaria, “Effect of Micro-holes Addition on the Natural Frequency and Mode Shape of Perforated Plates,” J. Adv. Res. Appl. Sci. Eng. Technol., vol. 11, no. 1, pp. 1–6, 2018.

A. Y. Ismail, M. Ulum, and A. Noerpamoengkas, “PENGARUH DIAMETER LUBANG, RASIO PERFORASI DAN SAMBUNGAN ANTAR PANEL TERHADAP FREKUENSI NATURAL PANEL BERLUBANG GANDA,” Pros. Semin. Nas. Sains dan Teknol. Terap., pp. 413–418, Sep. 2018.

A. Noerpamoengkas, M. Ulum, and N. Mahfoudz, “Studi Eksperimental Pengaruh Posisi dan Kedalaman Takikan U Terhadap Frekuensi Natural dan Respon Getaran pada Batang Kantilever Menggantung | Noerpamoengkas | Prosiding Seminar Nasional Sains dan Teknologi Terapan,” in Prosiding Seminar Nasional Sains dan Teknologi Terapan, 2019, pp. 367–372.

R. Raj, P. K. Sinha, and E. V. Prakash, “Modelling , Simulation and Analysis of Cantilever Beam of Different Material By Finite Element Method , Ansys & Matlab,” Int. J. Eng. Res. Gen. Sci., 2015.

V. Dive, M. Bhosale, V. Chavan, and N. Durugkar, “Analysis of Natural Frequencies of Cantilever Beam Using Ansys,” Int. Res. J. Eng. Technol., vol. 4, no. 5, pp. 2724–2728, 2017.

V. Kumar, K. Kumar Singh, and S. Gaurav, “Analysis of Natural Frequencies for Cantilever Beam with I-and T-Section Using Ansys,” Int. Res. J. Eng. Technol., vol. 2, pp. 1013–1020, Sep. 2015.

J. W. Jones, R. E. Nickell, and W. Bulat, “The Effects of Gravity on Structural Vibration,” in Volume 8: Seismic Engineering, 2013, p. V008T08A044.

L. N. Virgin, S. T. Santillan, and D. B. Holland, “Effect of gravity on the vibration of vertical cantilevers,” Mech. Res. Commun., vol. 34, no. 3, pp. 312–317, Apr. 2007.

D.-O. Kim, W.-S. Choi, K.-B. Park, and W.-J. Lee, “Natural Frequency Shift of a Graphite Column by Gravity,” in Transactions, SMiRT 19, 2007, p. K11/2.

G. N. Prasanna, “Static Analysis of aTapered Beam Using Excel and Ansys,” Int. J. Sci. Res., vol. 7, no. 4, pp. 282–285, 2018.

L. Jakubovičová, A. Sapietová, and J. Moravec, “Static analysis of transmission tower beam structure,” MATEC Web Conf., vol. 244, p. 01011, 2018.

K. A. Oladejo, R. Abu, and O. A. Bamiro, “Model for Deflection Analysis in Cantilever Beam,” Eur. J. Eng. Res. Sci., vol. 3, no. 12, pp. 60–66, Dec. 2018.




DOI: https://doi.org/10.35308/jmkn.v6i1.2305

Refbacks

  • There are currently no refbacks.