Menurunkan Waktu Penggantian Tabung Gas Welding (GMAW) Menggunakan Metode Single Minute Exchange Die (SMED) di Politeknik Astra

Neilinda Novita Aisa, Rahayu Budi Prahara, Eduardus Dimas Arya Sadewa, Wahyudi Wahyudi, Andreadie Wicaksono

Abstract


Politeknik Astra is a high vocational education institution that have several laboratories. Welding laboratoy has longest preparation time compare to another laboratories. Gas cylinder changes process in Gas Metal Arc Welding (GMAW) takes 29.2 minutes, which is the longest preparation time so the welding training is hinder by it. Previous condition of  gas instalation is, every GMAW machine equiped with one  gas cylinder,  so if the cylinder is run out of  gas, it have to changes and potentially it could be done more than one machine. The aim of this research is to reduce gas cylinder changes time in welding laboratory using single minute exchange of dies methode (SMED). SMED is one of lean manufacturing metodes that able to identified and reduce or eliminate time waste by separated internal setup and external setup. Using SMED metods, gas cylinder changes activities are identified then divided by internal and external setup. The activities that have no effect to gas flow from cylinder to machine are convert from internal to external setup. For the final, external setup are simplified using 5W2H tools. The solution that reserearcher found using SMED method is to built a centralized gas system with one cylinder as an active gas supply for whole GMAW machine and the other one as  a backup cylinder, in stead of install  gas cylinder on every GMAW machine. The result of this research is setup time for gas cylinder changing process is reduce from 1752 seconds or 29.2 minutes to 877 seconds or 14.6 minute or reduce 50%, furthermore man power alaso reduce from 3 person to 1 person.

Keywords


SMED; Welding; Sentralisasi Gas

Full Text:

PDF

References


A. Dwi, W. Wibowo, J. Arief, and R. Hakim, “Implementasi Metode Single Minute Exchange of Dies ( SMED ) dan Maynard Operation Sequence Technique ( MOST ) untuk Perbaikan Waktu Proses Produksi ( Studi Kasus Departemen Produksi- Wrapping di PT . X Surabaya ),” SENASTITAN 1, 2021.

Ö. Kabak and F. Ülengin, “Knowledge-Based Systems Cumulative belief degrees approach for analyzing the competitiveness of the automotive industry,” 2014, doi: 10.1016/j.knosys.2013.09.006.

R. Godina, Carina Pimentel, F.J.G. Silva, Joao C.O. Matias, “Improvement of the Statistical Process Control Certainty in an Automotive Manufacturing Unit,” Procedia Manuf., vol. 17, pp. 729–736, 2018, doi: 10.1016/j.promfg.2018.10.123.

D. F. Hidayat, J. Hardono, and T. M. Santoso, “Perbaikan Waktu Set-up Menggunakan Metode Single Minute Exchange Die ( SMED ) di PT . HP Improvement Set-up Time Using Single Minute Exchange Dies ( SMED ) Method at PT . HP,” J. Ind. Manuf., vol. 5, no. 1, pp. 18–22, 2020.

P. G. Ferradás and K. Salonitis, “Improving changeover time : a tailored SMED approach for welding cells,” Procedia CIRP, vol. 7, pp. 598–603, 2013, doi: 10.1016/j.procir.2013.06.039.

D. Van Goubergen and H. Van Landeghem, “Rules for integrating fast changeover capabilities into new equipment design,” Robot. Comput. Integr. Manuf., vol. 18, pp. 205–214, 2002.

A. Astuti and W. Rahayu, “Implementasi Single Minute Exchange Of Dies ( Smed ) Untuk Perbaikan Proses Brand Changeover Mesin Focke Dan Protos,” vol. 5, no. 1, pp. 8–15, 2020.

N. C. T. Angin, “Identification of internal dynamics of Türkiye ’ s furniture industry in the context of lean manufacturing integration maturity,” BMIJ, vol. 10, pp. 483–501, 2022.

A. Azizi, “Designing a Future Value Stream Mapping to Reduce Lead Time using SMED-A Case Study,” Procedia Manuf., vol. 2, no. February, pp. 153–158, 2015, doi: 10.1016/j.promfg.2015.07.027.

H. H. Azwir, N. C. Wijaya, and H. Oemar, “Implementasi Metode Single Minute Exchange Of Die Untuk Mengurangi Waktu Persiapan dan Penyesuaian Mold di Industri Polimer,” vol. 8, no. 2, 2021.

R. Godina, Carina Pimentel, F.J.G. Silva, Joao C.O. Matias, “A Structural Literature Review of the Single Min: Latest Trends Die,” Procedia Manuf., vol. 17, pp. 783–790, 2018, doi: 10.1016/j.promfg.2018.10.129.

M. Brito, A. L. Ramos, P. Carneiro, and M. A. Gonçalves, “Combining SMED methodology and ergonomics for reduction of setup in a turning production area,” Procedia Manuf., vol. 13, pp. 1112–1119, 2017, doi: 10.1016/j.promfg.2017.09.172.

M. Alejandra, B. Gerónimo, L. Cecilia, and S. Lostaunau, “Analysis of the Implementation of the SMED Methodology to Reduce Machine Setup Times and Die Change in the Food Industry : A Literature Review,” 2022.

G. Farhan et al., “Single Minute Exchange Die ( SMED ): A sustainable and well-timed approach for Bangladeshi garments industry,” Clean. Eng. Technol., vol. 12, no. November 2022, p. 100592, 2023, doi: 10.1016/j.clet.2022.100592.

A. Ali, “Lean Manufacturing Approach using SMED Method and Value Stream Mapping on The Spring Beds Production Floor,” pp. 613–626, 2022.

L. C. Setiawan, “Mereduksi Waktu Setup Menggunakan Metode Smed Pada Mesin Iss Kemas Pt Phapros Tbk Semarang,” Ind. Eng. Online J., 2023.




DOI: https://doi.org/10.35308/jopt.v9i2.7475

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 Jurnal Optimalisasi

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

JOPT: Jurnal Optimalisasi Indexing and Abstracting by: