Analisis Perawatan Cutter Section Dredger Dengan Metode FMEA dan OEE

Intan Hardiatama, Norman Audi Erlangga Pradipta Yudah, Robertus Sidartawan, Hari Arbiantara Basuki, Franciscus Xaverius Kristianta

Abstract


The development of technology and industry is currently being followed by increasing demand from the industry for mining or mineral materials, one of which is tin. Indonesia as the second largest tin producing country in the world plays a very important role in the development of technology and industry in the world. In Indonesia, tin mining is carried out by several companies, one of which is PT Timah (Persero) Tbk. This study aims to determine the effectiveness of the KIP 17 dredger system is 77% and the critical components obtained are the shaft and joint on the pump. The results of the analysis using Fishbone diagrams show that the quality of bolts and nuts and sealsused is not good. With the results of the study, it is recommended to increase personnel, especially in maintenance activities, and to improve the quality of nuts, bolts, and seals so as not to cause water to enter which can damage core components.

 

KeywordsMining, FMEA, Dredger

 


Full Text:

PDF

References


S. A. Miedema, “Dredging processes The cutting of sand, clay and rock cutting theory,” 978-94-6186-249, 2013.

A. Bonar and T. Sitepu, “Kajian Performansi Pompa Slurry pada Cutter Suction Dredger dengan Variasi Sudut Gali 35°, 40° dan 45°,” Talent. Conf. Ser. Energy Eng., vol. 1, no. 1, 2018, doi: 10.32734/ee.v1i1.107.

P. D. T. O’Connor and A. Kleyner, Practical reliability engineering: Fifth edition. 2011.

A. Darmawan, A. Rapi, and S. Ali, “Analisis Perawatan Untuk Mendeteksi Risiko Kegagalan Komponen Pada Excavator 390D,” J. Ilm. Tek. Ind., vol. 15, no. 2, 2017, doi: 10.23917/jiti.v15i2.2139.

K. Cicek, H. H. Turan, Y. I. Topcu, and M. N. Searslan, “Risk-based preventive maintenance planning using Failure Mode and Effect Analysis (FMEA) for marine engine systems,” 2010.

D. H. Triwardani, A. Rahman, and C. F. Mada Tantrika, “Analisis Overall Equipment Effectiveness (Oee) Dalam Meminimalisi Six Big Losses Pada Mesin Produksi Dual Filters Dd07 (Studi Kasus : PT. Filtrona Indonesia, Surabaya, Jawa Timur),” J. Rekayasa dan Manaj. Sist. Ind., vol. 1, no. 2, 2013.

S.Nakajima, “Introduction to TPM: Total Productive Maintenance.pdf,” Product. Press. Cambridge, 1988, doi: http://www.plant-maintenance.com/articles/tpm_intro.shtml.

R. Imanuell and M. Lutfi, “Analisa Perawatan Berbasis Keandalan Pada Sistem Bahan Bakar Mesin Utama KMP. Bontoharu,” JST (Jurnal Sains Ter., vol. 5, no. 1, 2019, doi: 10.32487/jst.v5i1.540.

D. I. Situngkir, “Pengaplikasian FMEA untuk Mendukung Pemilihan Strategi Pemeliharaan pada Paper Machine,” FLYWHEEL J. Tek. Mesin Untirta, vol. 1, no. 1, 2019, doi: 10.36055/fwl.v1i1.5489.

Vincent Gaspersz, “Metode Analisis Untuk Peningkatan Kualitas,” in Metode Analisis Untuk Peningkatan Kualitas, 2003.

S. Slameto, “The Application of Fishbone Diagram Analisis to Improve School Quality,” Din. ILMU, vol. 16, no. 1, 2016, doi: 10.21093/di.v16i1.262.




DOI: https://doi.org/10.35308/jmkn.v8i1.5454

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.